SuperFAST Non-Stick Grid Plate - 42" Utility For Goldman, Hoffman/New Yorker & Prosperity

Are you noticing wrinkles on all types of fabrics or just lighter weight materials? If it’s lighter weight materials you may want to reconsider your grid plate. The Hi-Temp Fabric (without flannel) and Non-Stick Coated Grid Plates are the best for pressing lighter weight materials. If you are already using one of these grid plates, make sure that your vacuum on the buck is operating correctly.

Yes, they are symmetrical and can be used on both. Also, right handed press means the narrow end is on the right (left hand, narrow end is on the left). The press pads also have the draw cord on the wide end. The Legger press pads have the draw cord on the narrow end.

We assume you have a non-stick coated grid plate and not a fabric covered one. You would not want to use steel wool in the non-stick coating of the grid plate as it could compromise the coating.

This grid plate works well and will provide a sharp press for all garments, however, it can also leave a shine. You can lay a cloth down over garments that would be effected by this, or we would also recommend the Hi-Temp Fabric grid plate. The Hi-Temp Fabric grid plate will provide a crisp press and eliminate shine.

About 1-2 years.

This problem is normally noticed on lighter fabrics, such as rayon. The reason for this occurrence is due to too much steam pressure coming from the top of the press. The top steam pressure should be shut off or reduced for about 3 weeks. As a press gets older the holes at the head of the machine get wider as well. More steam starts to flow from it. Because a new grid plate will function more efficiently, due to the fact that materials are more “breathable” and there is less starch, sizing or chemical build-up, the grid plate doesn’t need as much top steam to press. After about 3 weeks when the press pad isn’t as new, the top steam can be increased as necessary.

These are coated twice and heat set.

Water coming from the head of the grid plate is typically caused by a bad or dirty steam trap, a bad or dirty check valve, or by the vacuum not working properly. Typically a water issue will be seen more with a Non-Stick Grid Plate, because unlike the Hi-Temp Grid Plate, there is no fabric to absorb the moisture. A grid plate does not cause a water problem.

The grid plates we carry all come with instructions. For safe installation, install grid plate when the steam has been shut off and the press is cold. First, detach the springs from the worn grid plate and remove the grid plate from the head of the machine. Next, clean the rust off the head of the machine, using a soft wire brush or a hot head mitt. Then, to install the new grid plate, fit the grid plate onto the press head. Place springs over the top and hook springs into the eyelets to secure the grid plate. After, bring the head down and secure it by locking it. Push and bend the edges of the grid plate around the head. This will ensure a tight fit and will eliminate steam escaping from the edge of the head.

This product is a heat tolerant and chemical resistant substance. It can be found in either fiber or polymeric resin form. The polymeric resin is best known for providing a non-stick surface.

The coating is baked on, so it won’t peel or flake off. There is also an offset diffuser that will eliminate jet marks, and will evenly distribute heat and steam.

This typically happens when pressing silks or thinner fabrics. The way to fix this would be to change from a Hi-Temp grid plate to a Non-Stick grid plate.

Cleaner's Supply currently offers two different types of grid plates. The Coated Non-Stick Grid Plate is ideal for silk, wool, denims, and other fine fabrics. It provides a crisp press. This grid plate has a special non-stick coated metal surface. There is a diffuser on the inside to provide an even steam flow and to eliminate jet marks. The smooth surface virtually eliminates lifting and rolling of garments. Our High Temp Grid Plate is generally used for all types of fabrics including wool, blends, knits and other synthetic materials. The cover is made of a high-heat resistant material. There is a diffuser on the inside to provide even steam flow and to eliminate jet marks. The cover reduces moisture and condensate. The high-heat resistant cover eliminates shine and moire.